Arrowhead EKP1L Uživatelský manuál

1Owners ManualAV9000Eight Zone Downloadable PanelInstallation & ProgrammingManualProgrammed through the keypads orwith the ScanPro Downloader Sof

102.32 EKP1L INSTALLER CODE SPECIAL FUNC-TIONS:ENTERING PANEL PROGRAMMING[*&0] + [ I I I I ] + [0] + [#]EXITING PANEL PROGRAMMING[*&#]ENTER

112.33 LCD KEYPAD PROGRAMMING: FIGURE 4MemoryLocationEKP1L - LCD KEYPAD EEPROM MEMORY MAPNUMERIC DATA - ( 0 - 3 ) 0Keypad ID ( Starts from 0 ) (Select

122.34 PROGRAMMING EXAMPLE: FIGURE 5ScanPro PROGRAMITEM # LOCATIONPhone number digits1 2 3 4 5 6 7 8 9 1011121314151617181920211001-021 1ST PHONE N

13FIGURE 635133 ZONE REPORT DELAY TIME (x10sec) (1 - 15)36134 AC & LOW BATTERY REPORT DELAY (x1min) (1 - 15)537135 FALSE ALARM SHUTDOWN COUNT (

142.35 RECEIVER FORMAT EXAMPLE: FIGURE 7CONDIT ION ACRON S CANPRO EXT ENDED 4+2 SILENT ADEMCOS UP ERF AS T DOWNLOADER KNIGHT S UP ERF AS TScenario #

15NOTES 1. The “T” in Acron Format (conditions A-H) indicates Zone 1 is still tripped. In addition to the alarm which caused the report, thestatus of

162.36 PROGRAMMING WORKSHEET: FIGURE 8ScanPro PROGRAMITEM # LOCATIONPhone number digits1234567891011121314151617181920211001-021 1ST PHONE NUMBER D

17FIGURE 935133 ZONE REPORT DELAY TIME (x10sec) (1 - 15)36134 AC & LOW BATTERY REPORT DELAY (x1min) (1 - 15)37135 FALSE ALARM SHUTDOWN COUNT (1

182.37 INSTALLER PROGRAMMINGCALL DOWNLOADER COMPUTERTo have the panel call the “ScanPro Downloader” the following se-quence is entered:Figure 10ANSWER

19SECTION 3: PROGRAMMING STEPSEach of the "Steps" below correspond to the Item numbers used inthe ScanPro Downloader software. The numbers

2TABLE OF CONTENTSFEATURE LIST OF THE NEW AV9000 CONTROL PANEL... 3SECTION 1: INST

20Format = SK4+2 Station Code = 5Keypad # = 2 Account # = 1234Duress Code = D Transmission = 1234D3 = Duress Code User #31234 52 = Station Code Ke

21NOTE: The upload/download code should only be sent to receiv-ers 1 and 2 since this code will automatically be sent to the ScanProduring communicati

22STEP 39 141 ASSIGNABLE OUTPUT RELAY 1 This outputmay be programmed to provide +12 V.D.C at the output terminalwhenever the selected condition o

23ZONE OPTIONSSTEP 46 185 DELAY GROUP 1 ZONE SELECT (1-8)There are two exit/entrance delay times available. These may beused independently for p

24PANEL FUNCTIONSSTEP 61 205 FUNCTION SELECT GROUP 1Use the following chart to set the first system function group:1 No EOL present 2 Call back s

25SECTION 4: COMPLIANCEINFORMATION TO USERThis equipment generates and uses radio frequency energy and if not installed and used properly, that is in

nication. Le materiel doit egalement etre installe en suivant une method acceptee de raccordement.Dans certains cas, les fils interieursde l’entrepris

SECTION 5: LIMITED WARRANTYWARRANTY AND LIABILITY LIMITATIONS AND DISCLAIMERLIMITED WARRANTYSentrol, Inc., warrants to the purchaser that under normal

3Feature List of the New AV9000 Control PanelStandard AV9000 FeaturesTime Tested "Reliability" manufactured into every panel.8 Zone Control

4SECTION 1: INSTALLATION INSTRUCTIONSGENERAL1.0 SYSTEM DESCRIPTIONThe ARROWHEAD Model AV9000 is an eight zone control panel/digital communicator alarm

519. TESTING THE LOCAL SYSTEM USING THE EKP1 or EKP1L:Arm the system in the TEST MODE. (Press: Access Code, MODE,TEST, then ENTER). The audible war

6FAULT ANALYSIS NOTESAfter the programmed number of reporting attempts, the commu-nicator stops trying to call and goes into a trouble condition indic

7SECTION 2: PROGRAMMING INSTRUCTIONSUsing the EKP1 and/or EKP1L to program the AV90002.0 INTRODUCTIONWhether you are an experienced installer/programm

82.4 SELECTION DATASelection Data displays specific data selected for special func-tions. For example: Burglary zones or fire zones, or DTMF dialing

9EKP1L - LCD KEYPADThe LCD keypad can be used to program the panel following theprocedures on the next few pages. In addition to programming thepanel